Skip to main content

Automation

Automation

  • 47 Topics
  • 118 Replies
47 Topics
D
dawal1337Inspiring
asked in Automation
Global Engineering Studio - Golden Config Template - How to re-iterate

Greetings,I am running into a problem trying to simplify Golden Template Configuration in Golden Engineering Studio (GES).I am unable to get the Golden Template Configuration in GES to re-iterate through all parsed line vtys (line vty 0 4, line vty 5 15, etc.) and validate children configuration. I was hoping to not have to hard-set in my template configuration the expected line vtys, I want that to be dynamic. My only concern is that each line vty has “transport input ssh” configured, for example.Is that possible? I have tried using the following Configuration Parameter in my Golden Template Configuration:Name: Line_VTYValue:line vty $line_vty_start $line_vty_end transport input ssh And mapped the respective vars with my parsers:$line_vty_start → $vty_start$line_vty_end → $vty_end  Alternatively, configured the following as my Golden Template Configuration (pretty much the same, but not using Configuration Parameter): line vty $vty_start $vty_end transport input ssh My Parser for the

190
D
J
jadomNew Participant
asked in Automation
http/https checks

Hi guys,Can we create http/https checks in Netbrain for monitoring remote endpoints?Cheers

80
J
RightGuy
RightGuyNew Participant
asked in Automation
How do I know what CLI commands NetBrain is executing on my devices?

Hey - I was wondering if there was some way that you guys can tell me where I can find the commands that NetBrains is using when it talks to my device?

5095
M
S
slodowic
asked in Automation
API changes in R12, not getting a list of all devices when using Get Devices API

Since the R12 upgrade, I'm not able to get all device using the API: /ServicesAPI/API/V1/CMDB/DevicesI'm only pulling 50 devices, and can’t seem to get the whole inventory. This was working fine previously. Anyone else running into a similar issue? Not sure if its an issue with my install and something changed or something with R12?

531
M
D
dpriorNew Participant
asked in Automation
See Palo Alto Firewall Configuration in Set Format?

When getting the configuration for Palo Alto Firewalls in the Network Intents it is not giving it in the set format so its hard to check for compliance. How would I be able to see the configuration of the Palo Alto Firewalls in a set format like the link below?https://knowledgebase.paloaltonetworks.com/KCSArticleDetail?id=kA10g000000ClHoCAK

1512
M
P
pjhenningNew Participant
asked in Automation
ADT Tables

Is it possible to have the ADT tables keeping the existing data and only update new data as an option?Example, once devices are queried, the information of online devices will be populated into the ADT, the next day, some of those devices might be offline and others online again, and again the table will only collect information of the online devices at that time and previous data will be lost because devices might be offline.Have ADT table that keeps building up on information as devices comes online.

651
S
C
Charan0105New Participant
asked in Automation
Device hostname change - Discovery

Hello,I have a router device which is already present in netbrain. So when someone changes the device hostname in the device, would it reflect on netbrain automatically? Also added to that, if we run discovery task using an api with the device ip, does it change the updated details in netbrain? Thanks in advance  Regards,Charan Kumar N 

1284
Y
G
Gio.GNew Participant
asked in Automation
Can you obtain raw command data (CLI, Configuration, SNMP, etc.) via Qapp script?

Hi! I was wondering if it would be possible to avoid using the typical Device Queue → For each Device → Command → Parse → DDT no-code sequence of NetBrain Qapps, and write it in code instead. I figured out how to loop through all the devices in the queue as the first two Nodes in the sequence would, but I’m a bit stuck on how to call the commands, as I’m not sure if there’s a built in API call I can use to do this or not. for row in $_device_queue.GetRows():    device = row['this']Getting raw input would be ideal. I don’t need help on the Parser bit or converting to a DDT as I’m quite familiar with regex and NetBrain’s Table API - so it’s really just the command part.My reason for the request, is that for a given device queue, I need to run a list of multiple different types of commands on each device. One command may be for getting the configuration, some are for CLI output, and some are for SNMP output, etc. I know about the loop-tables functionality, to be able to run multiple comma

952
G
V
VerbatimNew Participant
asked in Automation
QApp: Cisco Router, Extended Ping, MTU Dont Fragment

Hello, Can a QApp ping the IP on the other end of a link with the “don’t fragment” bit set to that link’s MTU? Can this be done for every interface on the router?

1444
A
C
Charan0105New Participant
asked in Automation
API call to add devices to a domain

I am new to Netbrain and I am trying to add the device to the Netbrain through the API call. What would be the correct API call that I need to perform to add a device to netbrain. 

2061
C
E
eschulzNew Participant
asked in Automation
Diff of vlans on multiple devices

Hello, I do have 4 cisco leave switches in a DC and I would like to check if all of them have the same vlans and vlan description on it.The possibel diff between the 4 shall be shown to the user.An Q-APP or an Intent would be great. It shall be the same functionality as a runbook (Diff) provides but for n switches and in an automation.A golden template would not work here as we do have multiple DC`s with different vlan´s, so we just need a comparism possibility here.br

1142
E
L
LorensoNew Participant
asked in Automation
Regexp in RESTAPI

Hello team, Is possible search in oneIPTable database by string ? In whole database ? Or use regular expression ? Problem is that when I open it via GUI a try search it goes via every field in database and is searching string as I type it to search. But when I want do it via REST API I can only go through  rows with one Key IP, old DNS, MAC et. But o want to go through whole database and find every device that contains in hostname  for example backbone.

821
prallu
H
harishchandrasFrequent Participant
asked in Automation
Parsers for Cisco Nexus Devices

Does anyone have device configuration breakup parser for cisco nexus devices.I see it available for cisco router devices but can’t be use for cisco nexus devices since catalyst devices configurations by exclamation (!) but same is not available in case of cisco nexus devices. 

31413
S
A
Andy KrapfNew Participant
asked in Automation
Network Speed Benchmarking

Does anyone have a Qapp that will help conduct a network speed test (like iperf)?  I want to automate a periodic test to prove speed over a longer period of time.

1681
pradeep.gaddameedi
C
clueless_userNew Participant
asked in Automation
How do I grab data via SNMP, display it, and alert if above a threshold?

We have some Infoblox DHCP/DNS servers that I’d like to poll DHCP scope usage and if above a certain percent, fire off an email. I’d like to display this scope usage data on a dashboard too if possible. I know the data is there in SNMP https://docs.infoblox.com/space/nios85/35418019/SNMP+MIB+Hierarchyhttps://docs.infoblox.com/space/nios85/35418019/SNMP+MIB+Hierarchy#ibDHCPOne-MIB I’m trying to figure out the best way to do this. Would I write a qapp for this? I can’t seem to find any up to date guides on how to grab this data, parse it, and present it. 

1301
C
S
slodowic
asked in Automation
Execute CLI Commands from the API

Is there some way to be able to execute CLI commands from the API and pull the files or output? It doesn’t seem there is a way to do it so I wanted to see if anyone has other methods that they have found that would work for this use case?  

4656
M
T
TimLangNew Participant
asked in Automation
Visual Parser$bool Variable

Can anyone share an example of processing a $bool variable in the Visual Parser.  Basically, what I would like to do is verify whether a certain command is present or not and put a true or false in an output table.For example, verify that the Nexus pim feature is enabled. Command in config is;feature pim

862
A
L
laurdNew Participant
asked in Automation
CSV report from Python script in QApp

Hello!Is there a way to export a CSV file by using the “Script” node in a QApp? I want to filter a table with more complex logic than the “Basic Output” or “Subtable” nodes that a QApp can provide, and then export it to a CSV file. Thank you!

1091
K
L
laurdNew Participant
asked in Automation
Device group members via E-mail

Hello!Is there a way to periodically send a list of the members of a device group via e-mail? I’m using a QApp that puts non-compliant devices in a device group.Thank you

361
C
M
mosessefahNew Participant
asked in Automation
API Call to Sync Devices

So my Company has a Single Truth application which has the an active device list. How do I get to sync up this device list into our NetBrain domain using API?Thanks!

801
C
A
aoursNew Participant
asked in Automation
Qapp Output to Report or Filtered Table

Hello all.  Just wanted to post here to see if this is even possible.  I have a Qapp that creates a CSV file with specific fields.  The purpose is to create a filtered table or report that shows all of our network switches and the amount of unused interfaces.  The CSV just has all the raw data.  I would still need to create some logic that says interface status is either “down” or “administratively down”, the last input is over a year or never, and the media type is one of many options (example:  10/100/1000BaseTX) as I want to exclude fiber interfaces.  For each row in the CSV, I want to just count these.  Then, ideally, the report would simply show 2 columns.Column 1              Column 2Switch 1 Name        Number of Unused PortsSwitch 2 Name        Number of Unused PortsDoes anyone know if this can be accomplished within NetBrain or would I just need to utilize something external and work with the raw CSV data?Thanks.

3136
K
E
eschulzNew Participant
asked in Automation
Verifying Device Compliance Using Intent

Hello, I found the nice How To to do compliance with a Q-APP.https://community.netbraintech.com/articles/knowledgebase/How-To-Verifying-Device-Compliance-30-10-2020Could you provide a similar How To, to do it with an Intent ? br

1241
R
T
tyanchukNew Participant
asked in Automation
Device Property mass updates

I created a device property for Last date of Support for old hardware for all devices in netbrainthru Tenent, GDR Data.  I can see the device propery at the end of the device propertiesand I can popout and edit the last date of support for 1 device and save with no issue.How do I update more than 1 device at a time. Thanks,Tony

1043
E
S
Shiva90New Participant
asked in Automation
interactice CLI commands

hi How can we enable interactive CLI commands on all devices at once. 

911
E
craineri
craineriFrequent Participant
asked in Automation
How do I validate configurations in our environment to ensure consistency.

Can anyone advise if there is a way to validate a base configuration to other like devices to ensure compliance and our standards are being followed.For example, I have a device or model that I would like to ensure all other devices are identical such asLogging AAA/TACACS ACL’s NTPMy approach, which doesn’t seem to be working was Create a Parser to capture Configuration for text fields that I would like to ensure are consistent. Create a NI for prior fields that need to match. Created a specific test group for selected devices.However, when I run the NI, it only compares the fields that I selected to the previous baseline for the device, not the device I want it to model.Any advise or direction appreciated. Thanks.

3156
craineri
Terms & ConditionsCookie settings
Community |  Ideas

Facebook |  Instagram |  Youtube |  Twitter |  LinkedIn
Privacy & Security Statement  |  Terms & Conditions |  Impressum  |  UK Modern Slavery Statement
Copyright © 2021 by NetBrain Technologies Inc. - All rights reserved.