Skip to main content

Welcome to NetBrain Exchange

Recently active
Help others

Charan0105New Participant

API call to add devices to a domain

I am new to Netbrain and I am trying to add the device to the Netbrain through the API call. What would be the correct API call that I need to perform to add a device to netbrain.

PuterFellerNew Participant

Palo Alto interfaces not discovered

I’m working in an inherited Netbrain install. One pair of our Palo Alto NGFWs only show HA and management interfaces, none of the physical ethernet interfaces. This causes issues when searching paths that run through these firewalls. A path search that traverses this firewall will start with a switch directly connected to the firewall. If the next hop from the layer 3 switch is an ethernet interface/zone on the Palo Alto, Netbrain places an End System on the map. The end system’s IP address is the one assigned to the PA ethernet interface. The path ends with this “end system” (and a Path Failed message: Gateway device was not found), as there is no apparent discovered route from the source zone to the destination zone in the firewall, and then to the eventual destination. When viewing the firewall’s config in Netbrain, the physical interfaces are listed, along with the virtual router’s associated zones, corresponding interfaces and routes. +++In comparison, a different pair of Palo Alt

eschulzNew Participant

Diff of vlans on multiple devices

Hello, I do have 4 cisco leave switches in a DC and I would like to check if all of them have the same vlans and vlan description on it.The possibel diff between the 4 shall be shown to the user.An Q-APP or an Intent would be great. It shall be the same functionality as a runbook (Diff) provides but for n switches and in an automation.A golden template would not work here as we do have multiple DC`s with different vlan´s, so we just need a comparism possibility here.br

VerbatimNew Participant

QApp: Cisco Router, Extended Ping, MTU Dont Fragment

Hello, Can a QApp ping the IP on the other end of a link with the “don’t fragment” bit set to that link’s MTU? Can this be done for every interface on the router?

TimLangNew Participant

Parser Exchange

Reiterive parsing when the same command appears multiple times.

Does anyone have a solution to parse multiple lines with the same constant. For example, it is easy to create a paragraph parser to parse both the switchport trunk allowed vlan and switchport trunk allowed vlan add commands, but it will only parse one of the switchport trunk allowed vlan add instances. The “add” option can appear a number of times under one interface. interface GigabitEthernet7/12 switchport switchport trunk encapsulation dot1q switchport trunk allowed vlan 1,11,19,21,194,240,400,403,413,451-454,511,552 switchport trunk allowed vlan add 660,666,667,672,711,719,725,810,820,830,832 switchport trunk allowed vlan add 833,961,965,966

LucyCRNew Participant

Netbrain data-server in disconnected state

Hi everyone,A couple of days ago suddenly in Service Monitor the data server is showing as offline and all services stopped. The thing is that actually the data service is on and responsive, and service monitor agent is running as well as all of the services.An even stranger thing is that when I restart the FS the data server appears as Connected with all the services running, but after a couple of seconds it goes back to Disconnected.Any ideas on this? Our Netbrin version is 10.1.15.10 in case is needed.

LucyCRNew Participant

Authentication error in Firewall

Hi again everyone.Is there a way to not to check SSH credentials in a Palo Alto Firewall in Netbrain? Our firewall rejects those kind of auth attempts (as many other FW do) so it appears as a validation error in the map and seeing it red is kind of nerve wracking. Thanks in advance

Manav AgarwallaNew Participant

General Discussion

NetBrain Architecture

I need guidance in comprehending the data flow and how the various NetBrain components(Worker/TaskEngine/FSC/Redis/RabbitMQ/Elasticsearch/DB) are used when an end user initiates a task through the browser-based thin client.

John ThomasonNew Participant

Shared Dashboard without Login

Is there a way to ‘expose’ a Dashboard to other team members that are not logged into Netbrain??Kind of like the ‘Functional Portal’ exposes maps, one ip table, or paths to members without using a seat license. Thank you,John ThomasonQuest Diagnostics

Troy MellonNew Participant

Trying to find if a certain value exists

On my Cisco 9400 switches, some have an SSD inserted and some don’t. I am trying to find a way to report on those who do have an SSD. The only way I know to check is to issue the show hardware command (the lines in green appear if the SSD is installed): ncmc-svsw-es03#show hardware...cisco C9407R (X86) processor (revision V01) with 1841385K/6147K bytes of memory.Processor board ID FOX2717PJK13 Virtual Ethernet interfaces144 Gigabit Ethernet interfaces16 Ten Gigabit Ethernet interfaces4 Forty Gigabit Ethernet interfaces32768K bytes of non-volatile configuration memory.15995688K bytes of physical memory.11161600K bytes of Bootflash at bootflash:.1638400K bytes of Crash Files at crashinfo:.234430023K bytes of SATA hard disk at disk0:.1638400K bytes of Crash Files at crashinfo-1-1:.11161600K bytes of Bootflash at bootflash-1-1:.234430023K bytes of SATA hard disk at disk0-1-1:.Base Ethernet MAC Address : 58:56:9f:56:cb:40Motherboard Assembly Number : 4A39Motherboard Serial

PuterFellerNew Participant

Palo Alto interfaces not discovered

I’m working in an inherited Netbrain install. One pair of our Palo Alto NGFWs only show HA and management interfaces, none of the physical ethernet interfaces. This causes issues when searching paths that run through these firewalls. A path search that traverses this firewall will start with a switch directly connected to the firewall. If the next hop from the layer 3 switch is an ethernet interface/zone on the Palo Alto, Netbrain places an End System on the map. The end system’s IP address is the one assigned to the PA ethernet interface. The path ends with this “end system” (and a Path Failed message: Gateway device was not found), as there is no apparent discovered route from the source zone to the destination zone in the firewall, and then to the eventual destination. When viewing the firewall’s config in Netbrain, the physical interfaces are listed, along with the virtual router’s associated zones, corresponding interfaces and routes. +++In comparison, a different pair of Palo Alt

VerbatimNew Participant

QApp: Cisco Router, Extended Ping, MTU Dont Fragment

Hello, Can a QApp ping the IP on the other end of a link with the “don’t fragment” bit set to that link’s MTU? Can this be done for every interface on the router?

TimLangNew Participant

Parser Exchange

Reiterive parsing when the same command appears multiple times.

Does anyone have a solution to parse multiple lines with the same constant. For example, it is easy to create a paragraph parser to parse both the switchport trunk allowed vlan and switchport trunk allowed vlan add commands, but it will only parse one of the switchport trunk allowed vlan add instances. The “add” option can appear a number of times under one interface. interface GigabitEthernet7/12 switchport switchport trunk encapsulation dot1q switchport trunk allowed vlan 1,11,19,21,194,240,400,403,413,451-454,511,552 switchport trunk allowed vlan add 660,666,667,672,711,719,725,810,820,830,832 switchport trunk allowed vlan add 833,961,965,966

LucyCRNew Participant

Netbrain data-server in disconnected state

Hi everyone,A couple of days ago suddenly in Service Monitor the data server is showing as offline and all services stopped. The thing is that actually the data service is on and responsive, and service monitor agent is running as well as all of the services.An even stranger thing is that when I restart the FS the data server appears as Connected with all the services running, but after a couple of seconds it goes back to Disconnected.Any ideas on this? Our Netbrin version is 10.1.15.10 in case is needed.

LucyCRNew Participant

Authentication error in Firewall

Hi again everyone.Is there a way to not to check SSH credentials in a Palo Alto Firewall in Netbrain? Our firewall rejects those kind of auth attempts (as many other FW do) so it appears as a validation error in the map and seeing it red is kind of nerve wracking. Thanks in advance

Manav AgarwallaNew Participant

General Discussion

NetBrain Architecture

I need guidance in comprehending the data flow and how the various NetBrain components(Worker/TaskEngine/FSC/Redis/RabbitMQ/Elasticsearch/DB) are used when an end user initiates a task through the browser-based thin client.

John ThomasonNew Participant

Shared Dashboard without Login

Is there a way to ‘expose’ a Dashboard to other team members that are not logged into Netbrain??Kind of like the ‘Functional Portal’ exposes maps, one ip table, or paths to members without using a seat license. Thank you,John ThomasonQuest Diagnostics

LorensoNew Participant

Regexp in RESTAPI

Hello team, Is possible search in oneIPTable database by string ? In whole database ? Or use regular expression ? Problem is that when I open it via GUI a try search it goes via every field in database and is searching string as I type it to search. But when I want do it via REST API I can only go through rows with one Key IP, old DNS, MAC et. But o want to go through whole database and find every device that contains in hostname for example backbone.

maciasangel1New Participant

NB University - Can't Enroll to NB101 - Intro to Automation

Hello everybody,I have a question about an issue that I’m having with NBU. I enrolled in NB101 but missed it due to the time difference. I am attempting to re-enroll into the lecture for a different time but it shows “absent” and does not allow me to re-enroll. Any advice would be greatly appreciated. Thank you,Angel

harishchandrasFrequent Participant

Parsers for Cisco Nexus Devices

Does anyone have device configuration breakup parser for cisco nexus devices.I see it available for cisco router devices but can’t be use for cisco nexus devices since catalyst devices configurations by exclamation (!) but same is not available in case of cisco nexus devices.

Innovate with NetBrain

Have feedback or suggestions for our product? Submit and vote on product ideas.

Events Calendar

Leaderboard

Show full leaderboard

Badge winners

gkmurthyhas earned the badge Product expert
leadwesthas earned the badge Innovator
vamsihas earned the badge November 2023 Automation Hackathon GOLD
Venkata_Rao_Vemulahas earned the badge November 2023 Automation Hackathon GOLD
yogeshhas earned the badge November 2023 Automation Hackathon GOLD

Show all badges

NetBrain University

Need more help?

General Documentation

Everything you need to know about our platform including setup guides, etc.

Contact support

Contact our support team and we'll be happy to help you get up and running!

Knowledge Base

Find all the guidance you need as you navigate through our Knowledge Base

Powered by Gainsight

Terms & Conditions Cookie settings

Sign up

Already have an account? Login

Sign in with SSO

Login via NetBrain University

or

Username *

E-mail address *

Password *

I accept the terms & conditions

loginBox.register.email_repeat

Login to the community

No account yet? Create an account

Sign in with SSO

Login via NetBrain University

or

Username or Email

Password

Remember me

Forgot password?

Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.

Enter your e-mail address

Back to overview

Scanning file for viruses.

Sorry, we're still checking this file's contents to make sure it's safe to download. Please try again in a few minutes.

OK

This file cannot be downloaded

Sorry, our virus scanner detected that this file isn't safe to download.

OK