Skip to main content

Ask for Help

Ask help on the Hackathon.

  • 9 Topics
  • 11 Replies
9 Topics
P
PuterFellerNew Participant
asked in Ask for Help
Palo Alto interfaces not discovered

I’m working in an inherited Netbrain install. One pair of our Palo Alto NGFWs only show HA and management interfaces, none of the physical ethernet interfaces. This causes issues when searching paths that run through these firewalls. A path search that traverses this firewall will start with a switch directly connected to the firewall. If the next hop from the layer 3 switch is an ethernet interface/zone on the Palo Alto, Netbrain places an End System on the map. The end system’s IP address is the one assigned to the PA ethernet interface. The path ends with this “end system” (and a Path Failed message: Gateway device was not found), as there is no apparent discovered route from the source zone to the destination zone in the firewall, and then to the eventual destination. When viewing the firewall’s config in Netbrain, the physical interfaces are listed, along with the virtual router’s associated zones, corresponding interfaces and routes. +++In comparison, a different pair of Palo Alt

1091
G
4 months ago
L
LucyCRNew Participant
asked in Ask for Help
Netbrain data-server in disconnected state

Hi everyone,A couple of days ago suddenly in Service Monitor the data server is showing as offline and all services stopped. The thing is that actually the data service is on and responsive, and service monitor agent is running as well as all of the services.An even stranger thing is that when I restart the FS the data server appears as Connected with all the services running, but after a couple of seconds it goes back to Disconnected.Any ideas on this? Our Netbrin version is 10.1.15.10 in case is needed.

702
L
5 months ago
L
LucyCRNew Participant
asked in Ask for Help
Authentication error in Firewall

Hi again everyone.Is there a way to not to check SSH credentials in a Palo Alto Firewall in Netbrain? Our firewall rejects those kind of auth attempts (as many other FW do) so it appears as a validation error in the map and seeing it red is kind of nerve wracking. Thanks in advance

381
G
5 months ago
T
Troy MellonNew Participant
asked in Ask for Help
Trying to find if a certain value exists

On my Cisco 9400 switches, some have an SSD inserted and some don’t.  I am trying to find a way to report on those who do have an SSD.  The only way I know to check is to issue the show hardware command (the lines in green appear if the SSD is installed): ncmc-svsw-es03#show hardware...cisco C9407R (X86) processor (revision V01) with 1841385K/6147K bytes of memory.Processor board ID FOX2717PJK13 Virtual Ethernet interfaces144 Gigabit Ethernet interfaces16 Ten Gigabit Ethernet interfaces4 Forty Gigabit Ethernet interfaces32768K bytes of non-volatile configuration memory.15995688K bytes of physical memory.11161600K bytes of Bootflash at bootflash:.1638400K bytes of Crash Files at crashinfo:.234430023K bytes of SATA hard disk at disk0:.1638400K bytes of Crash Files at crashinfo-1-1:.11161600K bytes of Bootflash at bootflash-1-1:.234430023K bytes of SATA hard disk at disk0-1-1:.Base Ethernet MAC Address          : 58:56:9f:56:cb:40Motherboard Assembly Number        : 4A39Motherboard Serial

471
C
6 months ago
J
JackPrendergastNew Participant
asked in Ask for Help
Auto Intents into a Runbook

Hello, I am looking to put an auto-intent into a runbook. Reason being is that I can export the diagnosis output of intents into a word document. I dont think its natively possible to add an auto intent or auto intent profile into a runbook. Are there any work arounds? Any easy ways to add an auto intent/auto intent profile into a QAPP? Then add the QAPP into a runbook?The auto intents are crucial as the replication logic is something we will use all the time due to different environments, hostnames etc - hence discounting common intents without the auto-replication via auto intent. Thanks

361
pradeep.gaddameedi
7 months ago
J
jkbriggs78New Participant
asked in Ask for Help
What will I lose if I uninstall the entire IE and reinstall from scratch?

I had an oopsi and now cannot get my front server reconnected. In the 2 server deployment I accidently hit yes on the uninstall front server controller and then it no longer accepted the credentials but I do believe I was using the same credentials. One of the tests were successful for reconnecting to the front server but yet it would never reconnect. So I thought why not jump back another level and uninstall FS and FSC and start over, now I have even less than I previously had. Suggestions on how to not lose a ton of work but get this deployment healthy again?

391
A
7 months ago
A
akatwarooNew Participant
asked in Ask for Help
Parse Configuration File in Json format

I see an option option to parse json tables, however, I am not able to populate the “Data Scope”, which prevents me from moving forward. Is there a step that I’m missing?  Snippet of the config: Device:[    {        "_id": "abcdefg12345",        "address": "",        "dn": "abcdefg12345",        "isRealDev": true,        "isRealIntf": false,        "mac": "abcdefg12345",        "model": "device_model 1000",        "name": "abcdefg12345",        "networkName": "abcdefg12345",        "opTime": {            "$date": 1711950376000        },        "role": "primary",        "serial": "abcd-efg1-2345",        "tags": [            "recently-added"        ],        "wan1Ip": "100.100.100.100",        "wan2Ip": null

601
A
7 months ago
H
HaniNew Participant
asked in Ask for Help
Multiple client command in one parser

is it possible to add many cli command in one parser. version R11.1bex show version. show run | sec vtyI am trying to create a parser to run multiple show commands to check some security compliancy. see picture attached. thanks Hani,

612
H
10 months ago
D
Dug1609New Participant
asked in Ask for Help
How can one monitor SFP's w/ DOM for optical health threshold?

Hello. NetBrain R11.1I’d like to pull SFP DOM information to trigger warnings / alarms when threshold values are met. Digital Optical Monitoring (DOM) for monitoring SFP transceiver performance and temperature:Enable DOM on the device. Assumes DOM capable SFP’s are used Example:SW1(config)#transceiver type allSW1(config-xcvr-type)#monitoringSW1(config-xcvr-type)#endThen use the DOM specific commands to display details:SW1(config)#sh int gi 1/3 transceiver detail         Optical                  High Alarm  High Warn  Low Warn   Low Alarm         Transmit Power     Threshold   Threshold  Threshold  ThresholdPort     (dBm)                  (dBm)       (dBm)      (dBm)      (dBm)-------  -----------------  ----------  ---------  ---------  ---------Gi1/3      -27.7                  0.9            -1.0         -11.5       -13.5          Optical            High Alarm High Warn Low Warn Low Alarm         Receive Power    Threshold Threshold  Threshold  ThresholdPort     (dBm)              (

681
C
10 months ago
Terms & ConditionsCookie settings
Community |  Ideas

Facebook |  Instagram |  Youtube |  Twitter |  LinkedIn
Privacy & Security Statement  |  Terms & Conditions |  Impressum  |  UK Modern Slavery Statement
Copyright © 2021 by NetBrain Technologies Inc. - All rights reserved.